Cara Memperbaiki Mesin Cuci Pengering

>Hello Sohib EditorOnline, have you been facing issues with your washing machine dryer lately? Don’t worry, repairing it is not as difficult as it may seem. In this article, we will guide you through the process of fixing your washing machine dryer with 20 consecutive headings. So, let’s get started!

1. Identifying the Problem

The first step in repairing your washing machine dryer is to identify the problem. There could be various reasons that your washing machine dryer is not working as it should, including:

Problem	Solution
The dryer is not getting hot	Check the heating element and thermostat
The dryer is not spinning	Check the belt, motor, and pulleys
The dryer is making strange noises	Check the bearings, rollers, and idler arm

If you are unsure of what the problem could be, it’s best to call a professional.

2. Turning off Power Supply

Before starting to repair your washing machine dryer, you should turn off the power supply. This can be done by unplugging the machine from the wall or turning off the circuit breaker that supplies power to it.

3. Checking the Door

The first thing to check when your washing machine dryer is not working is the door. Make sure the door is fully closed and latched. If the door is open, the machine will not start.

3.1. Checking the Door Latch

If the door is closed but the machine is still not working, check the door latch. This is the mechanism that holds the door closed. If the latch is broken, the machine will not start. You may need to replace the latch.

3.2. Checking the Door Switch

If the door latch is working fine, you should check the door switch. This is a safety feature that prevents the machine from operating while the door is open. If the switch is defective, the machine will not start. You may need to replace the switch.

4. Checking the Power Cord

If the door is closed and latched but the machine is still not starting, you should check the power cord. Make sure it is securely plugged into a working outlet. You can also test the outlet by plugging in another appliance and seeing if it works.

4.1. Checking the Circuit Breaker

If the power cord and outlet are fine, you should check the circuit breaker. Make sure it is not tripped. If it is, reset it and try again.

5. Checking the Thermal Fuse

If your washing machine dryer is not getting hot, it could be due to a faulty thermal fuse. This is a safety device that prevents the machine from overheating. If the fuse is blown, the dryer will not heat up.

5.1. Locating the Thermal Fuse

The thermal fuse is usually located on the blower housing or exhaust duct. Refer to the owner’s manual for specific instructions on how to locate it.

5.2. Testing the Thermal Fuse

You can test the thermal fuse with a multimeter. Set the multimeter to the continuity setting and touch the probes to the thermal fuse. If there is no continuity, the fuse is blown and needs to be replaced.

6. Checking the Heating Element

If the thermal fuse is fine, the next thing to check is the heating element. This is the component that heats up the air inside the dryer. If it is faulty, the machine will not heat up.

6.1. Locating the Heating Element

The heating element is usually located on the back of the dryer. Refer to the owner’s manual for specific instructions on how to locate it.

6.2. Testing the Heating Element

You can test the heating element with a multimeter. Set the multimeter to the continuity setting and touch the probes to the terminals of the heating element. If there is no continuity, the element is faulty and needs to be replaced.

7. Checking the Thermostat

If the thermal fuse and heating element are fine, the next thing to check is the thermostat. This is the component that regulates the temperature inside the dryer. If it is faulty, the machine may not heat up properly.

7.1. Locating the Thermostat

The thermostat is usually located on the housing of the heating element. Refer to the owner’s manual for specific instructions on how to locate it.

7.2. Testing the Thermostat

You can test the thermostat with a multimeter. Set the multimeter to the continuity setting and touch the probes to the terminals of the thermostat. If there is no continuity, the thermostat is faulty and needs to be replaced.

8. Checking the Belt

If your washing machine dryer is not spinning, it could be due to a faulty belt. The belt connects the drum to the motor and pulleys. If it is broken or worn out, the drum will not spin.

8.1. Locating the Belt

The belt is usually located on the bottom of the dryer. Refer to the owner’s manual for specific instructions on how to locate it.

8.2. Inspecting the Belt

You can inspect the belt for signs of wear and tear. If it is cracked or frayed, it needs to be replaced.

9. Checking the Motor

If the belt is fine, the next thing to check is the motor. The motor is responsible for turning the drum. If it is faulty, the drum will not spin.

9.1. Locating the Motor

The motor is usually located at the bottom of the dryer. Refer to the owner’s manual for specific instructions on how to locate it.

9.2. Testing the Motor

You can test the motor with a multimeter. Set the multimeter to the continuity setting and touch the probes to the terminals of the motor. If there is no continuity, the motor is faulty and needs to be replaced.

10. Checking the Pulleys

If the motor is fine, the next thing to check is the pulleys. The pulleys are responsible for keeping the belt taut. If they are loose or damaged, the belt will slip and the drum will not spin.

10.1. Locating the Pulleys

The pulleys are usually located at the bottom of the dryer. Refer to the owner’s manual for specific instructions on how to locate them.

10.2. Inspecting the Pulleys

You can inspect the pulleys for signs of wear and tear. If they are loose or damaged, they need to be replaced.

11. Checking the Bearings

If your washing machine dryer is making strange noises, it could be due to faulty bearings. The bearings are responsible for keeping the drum balanced. If they are worn out, the drum will wobble and make noise.

11.1. Locating the Bearings

The bearings are usually located at the back of the dryer. Refer to the owner’s manual for specific instructions on how to locate them.

11.2. Inspecting the Bearings

You can inspect the bearings for signs of wear and tear. If they are worn out, they need to be replaced.

12. Checking the Rollers

If your washing machine dryer is making a squeaking noise, it could be due to faulty rollers. The rollers are responsible for keeping the drum rotating smoothly. If they are worn out, they will cause the drum to squeak.

12.1. Locating the Rollers

The rollers are usually located at the back of the dryer. Refer to the owner’s manual for specific instructions on how to locate them.

12.2. Inspecting the Rollers

You can inspect the rollers for signs of wear and tear. If they are worn out, they need to be replaced.

13. Checking the Idler Arm

If your washing machine dryer is making a thumping noise, it could be due to a faulty idler arm. The idler arm is responsible for keeping tension on the belt. If it is worn out, it will cause the belt to loosen and the drum to thump.

13.1. Locating the Idler Arm

The idler arm is usually located at the bottom of the dryer. Refer to the owner’s manual for specific instructions on how to locate it.

13.2. Inspecting the Idler Arm

You can inspect the idler arm for signs of wear and tear. If it is worn out, it needs to be replaced.

14. Replacing the Door Latch

If your washing machine dryer is not starting because of a faulty door latch, you can replace it by following these steps:

14.1. Removing the Old Latch

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Open the dryer door.
3. Locate the screws that hold the door latch in place.
4. Remove the screws with a screwdriver.
5. Disconnect the wires from the old latch.
6. Remove the old latch.

14.2. Installing the New Latch

1. Connect the wires to the new latch.
2. Place the new latch in position.
3. Secure the new latch with screws.
4. Close the dryer door.
5. Plug the machine back in or turn on the circuit breaker.

15. Replacing the Door Switch

If your washing machine dryer is not starting because of a faulty door switch, you can replace it by following these steps:

15.1. Removing the Old Switch

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Open the dryer door.
3. Remove the screws that hold the switch in place.
4. Disconnect the wires from the old switch.
5. Remove the old switch.

15.2. Installing the New Switch

1. Connect the wires to the new switch.
2. Place the new switch in position.
3. Secure the new switch with screws.
4. Close the dryer door.
5. Plug the machine back in or turn on the circuit breaker.

16. Replacing the Thermal Fuse

If your washing machine dryer is not getting hot because of a blown thermal fuse, you can replace it by following these steps:

16.1. Removing the Old Fuse

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Locate the thermal fuse. Refer to the owner’s manual for specific instructions on how to do this.
3. Disconnect the wires from the old fuse.
4. Remove the old fuse.

16.2. Installing the New Fuse

1. Connect the wires to the new fuse.
2. Place the new fuse in position.
3. Secure the new fuse in place.
4. Plug the machine back in or turn on the circuit breaker.

17. Replacing the Heating Element

If your washing machine dryer is not getting hot because of a faulty heating element, you can replace it by following these steps:

17.1. Removing the Old Element

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Locate the heating element. Refer to the owner’s manual for specific instructions on how to do this.
3. Disconnect the wires from the old element.
4. Remove the old element.

17.2. Installing the New Element

1. Connect the wires to the new element.
2. Place the new element in position.
3. Secure the new element in place.
4. Plug the machine back in or turn on the circuit breaker.

18. Replacing the Thermostat

If your washing machine dryer is not getting hot because of a faulty thermostat, you can replace it by following these steps:

18.1. Removing the Old Thermostat

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Locate the thermostat. Refer to the owner’s manual for specific instructions on how to do this.
3. Disconnect the wires from the old thermostat.
4. Remove the old thermostat.

18.2. Installing the New Thermostat

1. Connect the wires to the new thermostat.
2. Place the new thermostat in position.
3. Secure the new thermostat in place.
4. Plug the machine back in or turn on the circuit breaker.

19. Replacing the Belt

If your washing machine dryer is not spinning because of a faulty belt, you can replace it by following these steps:

19.1. Removing the Old Belt

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Locate the belt. Refer to the owner’s manual for specific instructions on how to do this.
3. Release the tension on the belt by moving the idler arm or motor.
4. Remove the old belt.

19.2. Installing the New Belt

1. Place the new belt over the drum and onto the pulleys.
2. Apply tension to the belt by moving the idler arm or motor.
3. Make sure the belt is aligned properly and not twisted.
4. Plug the machine back in or turn on the circuit breaker.

20. Replacing the Motor

If your washing machine dryer is not spinning because of a faulty motor, you can replace it by following these steps:

20.1. Removing the Old Motor

1. Unplug the machine from the wall or turn off the circuit breaker.
2. Remove the belt from the motor pulley.
3. Disconnect the wires from the motor.
4. Remove the screws that hold the motor in place.
5. Remove the old motor.

20.2. Installing the New Motor

1. Place the new motor in position.
2. Secure the new motor in place with screws.
3. Connect the wires to the new motor.
4. Attach the belt to the motor pulley.
5. Plug the machine back in or turn on the circuit breaker.

FAQ

1. How often should I clean my washing machine dryer?

You should clean

Cara Memperbaiki Mesin Cuci Pengering